64×64 RGB LED Matrix – 3mm Pitch

95,08

64×64 RGB LED Matrix – 3mm Pitch COD: AF-4732

COD: AF-4732 Categorie: ,

Descrizione

Description

Winter time can be rough in the city. The sky is gray. The weather is unpredictable. So slough off those seasonal blues with some Times Square razzle dazzle from this sweet, ultra-high-density 64×64 RGB LED Matrix. These panels are typically used to make video walls. Here in New York we see them on the sides of buses and on top of taxi cabs displaying animations or video advertisements. We thought they looked really cool, so we picked up a few boxes of them from a factory. They have 4,096 bright RGB LEDs arranged in a 64×64 grid at a 3mm pitch

WARNING! These 64-pixel tall matrices use a non-standard 5-address multiplexing system!

Many add-ons or drivers use only a 4-address (ABCD) setup. You can use these matricies with our RGB Matrix Bonnet for Raspberry PiRGB Matrix HAT (you’ll need to connect a solder jumper) or Matrix Portal (ditto, jumper required). Other libraries such as our Arduino shield with Adafruit library or our HDMI driver boards don’t support 5-address multiplexing!

The SmartLED Shield in combination with the Teensy 3.5/3.6 has the hardware for driving these 5-address panels, and enough RAM to refresh the 4096 pixels, however the power plug must be manually soldered/adapted because the shield overlaps it.

Full Kit Contents:

  • 64×64 RGB panel
  • IDC ribbon cable (~16cm)
  • power cable (~50cm)

RAM & Processor Requirements

Keep in mind that these displays were designed to be driven by FPGAs or other high speed processors: they do not have built in PWM control of any kind. Instead, you’re supposed to redraw the screen over and over to ‘manually’ PWM the whole thing.

You’ll need about 1600 bytes of RAM to buffer the 12-bit color image. You cannot use this size panel with an Arduino UNO (ATmega328) or ATmega32u4 – you need a chip with more RAM! These displays are technically ‘chainable’ – connect one output to the next input – as long as you have the RAM and CPU to handle it

This display does best with a high speed, high RAM microcontroller like a SAMD21, SAMD51, ESP32, etc. 8-bit micros are going to struggle if they work at all. The good news is that the display is pre-white balanced with nice uniformity so if you turn on all the LEDs it’s not a particularly tinted white.

Power Requirements

There’s a lot of LEDs! You may need up to 4A per panel. We suggest our 4A regulated 5V adapter and then connecting a 2.1mm jack. Please check out our tutorials for more details!

Connection Requirements

These displays require 13 GPIO pins to control. You may have to use consecutive or special pins depending on the driver firmware. We’ll be honest: folks who try to wire directly are usually not successful, its easy to get confused and misconnect. For that reason we strongly recommend a ready-to-go board or adapter that makes wiring as easy as plugging in the cables and powering with 5V

  • We recommend the Matrix Portal ESP32-S3 for a WiFi-enabled powerful plug-and-play board
  • The original Matrix Portal with SAMD51 is also a great plug-and-play board if you happen to want a Cortex M4 as a main processor (we recommend the S3 version, above, as it is faster and has more memory)
  • For many Arduino-shaped boards, you may be able to use our RGB Matrix Shield (check the product page and tutorial for which Arduino-like boards can be used)
  • We also have RGB Matrix FeatherWings for many Feather boards (check the product page and tutorial for which Feather boards can be used)
  • For Raspberry Pi computers, our RGB Matrix Bonnet is fully plug-and-play for powerful Linux-controlled displays.

We’ve also got our great Protomatter library that works in Arduino and CircuitPython for quick usage of many chained matrices.

Please note! These panels are remainder stock from factories that make huge light boards. For that reason, the look and size might vary from batch to batch, even though the basic operation, codebase and tutorial is the same.

Note: This does not include 4 mounting screws and mini-magnets, however we do have them available separate here!

Technical Details

  • Brightness: 2800cd/square meter
  • Size: 192mm x 192mm
  • Pitch: 3M
  • 5 Addressable Pins
  • Compatible with M3 mounting screws
  • Scan: 1/32
  • Refresh Frequency: >=400HZ
  • Waterproof Class: IP43
  • Weight: 235g (only matrix panel) / 269g (w/ components)

Best for indoor use

 

  • CAD Drawing